How to achieve this mesh?

  • 1.1K Views
  • Last Post 10 June 2018
  • Topic Is Solved
Fabricio.Urquhart posted this 25 April 2018

Hello Peter,

 

I need a help for meshing point of stress concentration, like holes in plates. I have read a thesis work, like the picture below, but I could not do the same mesh. Do you know which method is possible to mesh like de picture?

Order By: Standard | Newest | Votes
peteroznewman posted this 26 April 2018

Hello Fabricio,

ANSYS has mesh controls that can provide a similar mesh. There is a mesh control called inflation that will put a layer of small elements around (or along) a boundary.

If you create the geometry and attach it to your reply, I can show you these mesh controls.

Regards
Peter

raul.raghav posted this 26 April 2018

Peter is right about the inflation layer. Attached is a workbench archive file which shows two different ways of meshing the geometry.

Refer to the pictures below. The first one is similar to the one you needed help with and the second one is a very easy way of meshing the geometry without any modification to the geometry but with inflation around the holes.

Rahul

Attached Files

Raef.Kobeissi posted this 06 May 2018

You can also use the Cut Cell method to apply a hexahedral mesh. I think ANSYS meshing tool would usually impose a hexa-dominant mesh for simple geometries like this one. 

Raef Kobeissi

Fabricio.Urquhart posted this 29 May 2018

@raul.raghav

Can you attach a Ansys 18.2 file?The beam and the end-plate have different materials (A572 and A36). So I do not know how I match the node between different bodies with bonded contact.

Thank you. 

 

 

Fabricio.Urquhart posted this 29 May 2018

Raef, the Cut Cell method is only to CFD analyse, isn't it?

raul.raghav posted this 30 May 2018

Fabricio, its a little more complicated to make the mesh conformal with multiple bodies as you want it. I've attached the workbench file showing you the steps and a pdf file which will walk you through the steps I performed to get a conformal mesh in the multiple bodies. The final mesh looks like:

Rahul

Attached Files

  • Liked by
  • peteroznewman
  • vganore
Fabricio.Urquhart posted this 05 June 2018

Raul, I reached a good mesh dividing the edges and some faces. So the geometry is simpler. And I think that it is not necessary to use "node merge" between the contact, I asked it for Peter, He said it. And results are becoming better. See what happen if I use the node merge.

What do you think about the mesh, In this exactly moment I am doing the convergence test, saving four or five model, increasing the number of nodes and mesh quality.

 

Thank you very much!!!!

peteroznewman posted this 06 June 2018

Fabricio,

I would divide the face on the base plate along the three planes of the beam that you want to represent as welded to the base plate, then use Node Merge. On other models, I have even created triangular solids to represent the weld bead and bonded that extra material to the model.

Regards,
Peter

  • Liked by
  • Fabricio.Urquhart
raul.raghav posted this 06 June 2018

Fabricio, node merge is important if you want a conformal mesh between the bodies. Without node merge the nodes of the bodies are free to move. Although they might appear conformal with uniform setting of "Multizone", they won't have conformity unless you use node merge. Again the requirement depends on what you're trying to model.

Rahul

  • Liked by
  • Fabricio.Urquhart
Fabricio.Urquhart posted this 10 June 2018

Thank you!

I will try it, divide the base plate along the three planes. Yes, I thought about modelling the weld, but for this master thesis I will not do it yet.

 

Thank you again!!!

Close